Driver for the Lunatone DALI-2 IoT gateway (art. 89453886, also the -NR and -EM versions). It controls the DALI and DALI-2 luminaires connected to the gateway and keeps Control4 in sync with their real state: if someone changes a light from a DALI button or the Lunatone app, Navigator follows right away.
Each luminaire, DALI group and gateway zone shows up in Control4 as a regular light, bound to a ZOOM – Universal Light V2. The driver creates a Universal Light V2 for each luminaire by itself. Dimmable, on/off, RGBW and tunable white (color temperature) lights are supported. Everything runs on the local network, no cloud.
Prerequisites
DALI-2 IoT gateway on the same network as the controller, with a fixed IP (static or DHCP reservation).
DALI luminaires addressed and registered in the gateway (with DALI Cockpit or this driver's scan actions). A luminaire that is not registered cannot be controlled on its own.
ZOOM – Universal Light V2 driver in the Documents\Control4\Drivers folder (included in the package). The driver creates one for each luminaire.
Internet access on the controller to activate the license.
Installation
Add the ZOOM – Lunatone DALI-2 IoT driver to the project.
Enter the gateway IP in IP Address. The default port is 80.
Check that Connection Status shows the gateway on-line. Gateway Name, Firmware Version and Registered Devices fill in on their own.
The driver creates one light connection for each luminaire, each DALI group in use, each gateway zone and one for all lights on the bus.
For each luminaire, the driver creates a ZOOM – Universal Light V2 in the gateway's room, named as in the gateway and already bound. Then just adjust each light's name and room.
Groups, zones and broadcast do not create a light by themselves. To use one, add a Universal Light V2 and bind its light connection to the desired connection of this driver (Connections tab).
The light type (dimmer, on/off, RGBW or tunable white) is detected automatically and can be changed on the Universal Light V2 itself.
Lights, groups and zones
Connection
What it controls
DALI <name> (A<n>)
One registered luminaire (address n).
DALI Group n
DALI group 0 to 15. Only shown when at least one luminaire belongs to it.
DALI Zone n
Zone created in the gateway.
DALI Broadcast (All)
Every luminaire on the bus at once.
For groups, zones and broadcast the level shown is the brightest luminaire. Connections are not renamed after they are created: if you rename a luminaire in the gateway, the connection keeps the old name.
Properties
Property
Description
License Key
Driver license key.
License Status
License or trial status.
Control4 MAC Address
Controller MAC, used by the license.
Driver Information
Latest driver messages.
Log Level / Log Mode
Log detail and destination.
IP Address
DALI-2 IoT gateway IP.
Gateway Port
Gateway port (default 80).
Connection Status
Whether the driver is talking to the gateway.
Check Connection Timer (s)
How often the driver checks the connection and reconnects if it drops.
KeepAlive Seconds
Interval of the signal that keeps the connection open.
Gateway Name / Firmware Version / Serial Number
Gateway data, filled in automatically.
DALI Bus Status
Whether the DALI bus is powered and working.
Registered Devices
Number of luminaires registered in the gateway.
Scan Status
Progress of the luminaire scan.
Auto Create Devices
New Only (default): creates the light only for new luminaires. New and Missing: also creates the ones with no light in the project. No: creates nothing.
Actions
Action
Description
Refresh Devices
Reads luminaires, groups and zones from the gateway again.
Scan DALI Bus (Address and Register New Devices)
Looks for new luminaires, addresses and registers them. Existing ones are not changed.
Scan DALI Bus (Register Only, No Addressing)
Registers luminaires without changing their addresses.
Cancel Scan
Stops a running scan.
Create Missing Light Drivers
Creates the Universal Light V2 for luminaires with no light in the project (for example, after deleting one by mistake).
Sync Light Bindings
Creates connections for new luminaires, groups and zones.
Remove Orphan Bindings
Removes connections for luminaires, groups or zones that no longer exist in the gateway. The Universal Light V2 bound to them is disconnected.
List Devices
Prints the luminaire list with level and groups in Lua Output.
A fresh installation scan (which deletes every registered luminaire) is intentionally left out of the driver. Run it from the gateway or DALI Cockpit.
Commands and events
Programming commands
All of them work on one luminaire, a group, a zone or all of them (broadcast).
Command
Description
Set Color Temperature
Changes the color temperature (Kelvin) of tunable white luminaires.
Recall Scene
Recalls one of the DALI scenes 0 to 15 stored in the luminaires.
Store Scene
Stores the current state as DALI scene 0 to 15.
Start Sequence / Stop Sequence
Starts or stops a sequence configured in the gateway.
Events
Event
When it happens
Device on-line
The gateway is answering again.
Device off-line
The gateway stopped answering.
Troubleshooting
Connection Status does not go on-line: check the IP, whether the gateway answers in a browser and whether the controller is on the same network.
Luminaire does not show up: it must be registered in the gateway. Run a scan and then Sync Light Bindings.
Light was not created automatically: the ZOOM – Universal Light V2 driver must be in the Documents\Control4\Drivers folder. Put the file there and use Create Missing Light Drivers.
Light does not respond in Control4: check that the Universal Light V2 is bound to the right connection and that the license is valid in License Status.
DALI Bus Status shows not powered: the DALI bus has no power supply or a wiring fault.
Licensing
30-day trial included; the remaining time is shown in License Status.
After purchase, enter the key in License Key.
The controller needs internet access to activate and periodically check the license.
Once a day, also during the trial, the driver reports technical data of the installation to the license server (controller model and version, driver version, project name and license state). No personal data is sent. When a new driver version is available, it shows in License Status with the link to the driver page on the website.
Initial release. Creates a light for each luminaire by itself, already bound, with tunable white support. Reports the installation's technical data to the license server once a day, which speeds up support, and shows in License Status when a new driver version is available.