ZOOM – Lutron QS Standalone Gateway v20261120

Driver: Control4 DriverWorks Platform: Lutron QS Standalone (QSE-CI-NWK-E interface) Minimum OS: 3.0

PT EN

Overview

Integrates Lutron QS Standalone systems with Control4 through the QSE-CI-NWK-E network interface. The driver finds the devices on the QS link by itself and creates the matching ZOOM Universal drivers.

Prerequisites

Installation

  1. Add the ZOOM – Lutron QS Standalone Gateway driver in Composer Pro, in the room where the devices should appear.
  2. Set IP Address to the QSE-CI-NWK-E IP. Login comes with the interface default; fill in Password only if the interface has one.
  3. With Connection Status = Connected, discovery runs by itself on the first connection (or run Discover Devices).
  4. The Universal drivers are created and connected automatically. Rename each one and move it to the right room in Composer.
Requirement: ZoomDH_Universal_Light.c4z, ZoomDH_Universal_Blind.c4z and ZoomDH_Universal_Keypad.c4z must be on the controller. If automatic creation fails, add one instance of each type manually in Composer (this sends the driver to the controller) and run Create Missing Devices.

Discovery tests the zones of each GRAFIK Eye and Energi Savr Node, so it may take a few seconds per device. Progress is shown in Discovered Devices.

Supported devices

Lutron deviceDriver createdNotes
GRAFIK Eye QSUniversal Light (one per zone) + Universal Keypad (scene buttons)Level 0–100% with ramp. Keypad with Scene 1–4 and Off; the active scene is in a gateway variable.
Energi Savr Node QS (0-10 V, Softswitch, Phase Adaptive, DALI, EcoSystem)Universal Light (one per zone)Level 0–100% with ramp (up to 90 seconds). Only zones configured in the Energi Savr Node show up.
QS motor module (QSE-CI-4M-D)Universal Blind (one per output)Open, close and stop only. Use Use Levels = Off and set the travel times.
Sivoia QS shadeUniversal BlindReal position 0–100%. Use Use Levels = On and Advanced Motor = On.
seeTouch QS keypad (including Int’l)Universal KeypadPress, release and hold events per button.
Wallbox Input Closure Interface (QSE-CI-WCI)Universal KeypadOne button per input (up to 8).
Pico (associated with a QS Sensor Module)Universal KeypadOn, Favorite, Off, Raise and Lower buttons. Each Pico shows up in Control4 the first time one of its buttons is pressed.
Others (QSE-IO etc.)—Ignored; listed in Unknown Devices.

If a keypad has a button outside the default layout, it is added to the Control4 keypad automatically the first time it is pressed (up to 10 buttons).

In QS Standalone, Lutron does not allow keypad LEDs to be controlled through integration: they keep following the keypad's own programming.

Picos

In QS Standalone, Picos talk to the system through the QS Sensor Module, which does not report which Picos are associated. After discovery, press one button on each Pico: the "<sensor module> Pico N" keypad is created at that moment and responds from the next press on.

Names

In QS Standalone, devices have no name or room. The driver uses the Integration ID stored in the interface (e.g. Living GRAFIK Zone 2); without one it uses the type and serial number (e.g. GRAFIK Eye 00AC123D Zone 2). The serial number is also on the device label.

All devices are created in the gateway room. Once created they can be renamed and moved freely: the link to the Lutron device does not change.

GRAFIK Eye scenes

Properties

PropertyDescription
IP AddressQSE-CI-NWK-E IP.
PortInterface port (default 23).
Login / PasswordInterface access. The default login is pre-filled; the password is only used if the interface asks for one.
Connection StatusConnection state.
InterfaceInterface model, serial number and firmware.
Discovered DevicesNumber of zones, shades and keypads found.
Unknown DevicesQS link devices the driver does not control.
GRAFIK Eye ScenesActive scene of each GRAFIK Eye.
Auto Create DevicesNew Only (default): only creates what discovery found for the first time; a driver deleted on purpose does not come back. New and Missing: also recreates missing ones. No: creates nothing by itself.
Auto Discover On ConnectRuns discovery on the first connection if nothing has been discovered yet.
License Key / License StatusDriver license (see Licensing).
Log Level / Log ModeLog detail for troubleshooting.

Actions

ActionDescription
Discover DevicesLooks for the devices on the QS link. Running it again duplicates nothing and adds new devices.
Create Missing DevicesCreates the Universal drivers that are missing.
Refresh AllRefreshes the level of every zone and shade and the GRAFIK Eye scenes.
ReconnectReconnects to the interface.
Select GRAFIK Eye SceneActivates a scene on the chosen GRAFIK Eye.
Show DevicesLists the devices found and the drivers created in the Lua log.
Send Command (diagnostics)For technical support (only with support mode enabled).
Clear DiscoveryRemoves all connections and everything discovered (confirm with Yes). Universal drivers are not deleted.

Commands and events

ItemDescription
Select Scene commandActivates the chosen scene (0 = Off) on the chosen GRAFIK Eye.
Scene Changed eventA GRAFIK Eye changed scene (from Control4, the GRAFIK Eye itself or a keypad).
<name> Scene variablesActive scene of each GRAFIK Eye, for use in conditionals.

Programming example

When  Keypad Entry → Button 1 pressed
Do    ZOOM Lutron QS Standalone Gateway → Select Scene "Living GRAFIK" scene 2

Troubleshooting

SymptomLikely cause / fix
Connection timeoutWrong IP or interface off the network.
Login failedWrong login or password. Check whether the interface has a password set.
No devices answeredThe interface does not see the QS link: check the link wiring and device power.
Device in Unknown DevicesType not supported yet. Send the property text to support.
GRAFIK Eye or Energi Savr without zonesThe device did not answer during discovery. Run Discover Devices again.
Keypad button does not trigger in Control4Check in the interface that button events are enabled for integration.
Universal driver not createdDriver missing on the controller; see Requirement in Installation.

To investigate, use Log Level = 5 - Trace and Log Mode = Print: all communication shows in Composer's Lua tab.

Licensing

What the license controls

OperationTrial activeTrial expired
Connection and discoveryOKOK
Level, scene and button feedbackOKOK
Light commands (level, ramp)OKBlocked
Shade commands (open, close, position)OKBlocked
Select SceneOKBlocked

Support and Updates

Release Notes

VersionDateDescription
20261120 11/20/2026 Initial version: GRAFIK Eye QS and Energi Savr Node (0-10 V, DALI and EcoSystem) zones as lights, Sivoia QS shades, motor module outputs, seeTouch QS keypads, input closure interfaces and Picos, and GRAFIK Eye scenes, all found and created automatically.